Installation Instructions - Custom Seat Covers
Original Look - Hawaiian -
Neo-Supreme Installation
INSTALLATION INSTRUCTIONS:
1. On seat coves with separate back
and bottoms, start with bottom portion of seat
covers.
2. Attach supplied hooks on each strap and
pinch with pliers to secure strap.
3. Line up seat
cover bottoms on correct portion of seats. Pull towards back
so that the seams on the seat cover line up with the seams on
the seat.
4. Push the straps through the space
between seat back and the seat bottom and attach to the
underside of the seat. Do not hook them to the seat
control wires or the fixed frame of the
seat.
For Backrests without separate
Headrests:
5. Slip backrest of the seat cover
over the backrest of the seat and pull down tight over the
seat. Always pull on seat cover material not on
the stretch fabric.
6. Push
material Flap with straps on bottom of backrest cover between
seat back and bottom. These straps go up the back of the seat
and hook to the straps on the inside, at top of the seat
cover. These straps should be hidden behind the stretch
material back.
Note: Hooking the
backrest to itself allows the seat backs to move forward or
back without wrinkling. It also gives a neater look (by hiding
the flap) from the back of the seat.
For Backrests with
Moveable
Headrests:
Seat
Backrests:
1. Remove
Headrests.
A. On non-removable headrests
the seat cover will have Velcro at the
top.
B. For GM/Chevy seats:
- Where the headrest post goes into the seat
there is a plastic cap.
- Push a small nail or
heavy paper clip into hole and pull up to release
headrest.
C. Ford Headrest removal:
- On the driver's side post grommet there is a little
plastic tip sticking up on the inner side of the grommet.
On the passenger side post grommet, outer side, there is a little flush
button that looks like part of the grommet. Press the tip
on the outer grommet in, while at the same time using a small
screw driver to press in on the flush button on the opposite post.
Both must be pressed at the same time. There is sufficient room
to allow the fist to push upward and release the headrest posts from their
notched stops.
2. Follow steps 5 & 6 above.
It may be necessary to cut small holes in
the seat covers for the headrest posts. To do this, feel for
the holes on top of the backrest through the seat covers. Lift
the material from the seat and cut a small hole with sharp
knife just enough for the headrest post to slide through. Then
put the headrest back in. Do not poke through
the cover while it is against the seat.
Headrest Cover
Installation:
The best
way to install headrest covers is to have the headrests in the
seat. Before slipping on the headrest covers, make
sure they are facing the right way. To do this put both hands
in the headrest cover and compare it with the headrest on your
seat to see the correct way it goes on. Headrest covers
are usually tight for a great fit. Slip one side of the
headrest cover over one side of the headrest. Then slip the
other side of the headrest cover over the top of the headrest
and pull all the way down. As you do this, squeeze the foam of
the headrest in with your hands to accommodate stretching the
fabric over the headrest.
Caution:
A sudden release
of the hook attached to fastening straps can cause serious eye
damage. Look for the hook up spot and then move your head away
from the line of sight when pulling and attaching straps.
Safety glasses should be used while
installing.
Care & Cleaning:
These seat
covers should be hand washed in mild soap and warm water. Hang
to dry.
Note: Purchaser assumes
responsibility when cleaning.
Warranty:
All seat covers are warranted against defective materials and workmanship for
a period of 1 year from the date of purchase.
|
